Electric Underfloor Heating for Tiles

Electric underfloor heating is both easy and inexpensive to fit under Tiles. It is one of the most common floor coverings used over the top of electric underfloor heating.

When installing tiles over electric underfloor heating mats, there are several important considerations to keep in mind. Here are some key points to consider:

1) Planning Stage

underfloor heating build up under tile

Choosing the Type of Tiles: Most types of tile such as Porcelain and Ceramic are compatible with the Rayotec Webtech electric underfloor heating mats system which makes them cheap and easy to install.

What flooring is compatible with the Rayotec Webtech mats? Most Tiles and Vinyl are compatible but always check the flooring manufacturer's guidelines to ensure compatibility with both electric underfloor heating and the installation method. You can also use them for stuck down wood, for floating wood you will need our Foil heating mats which can be found here.

Check Available Floor Height: It’s important to check the boundaries of your room and work out the available floor height and make sure everything will fit. There is 2 types of insulation board for under the Webtech mats so you need to make sure you are planning for the correct one. If you have a wooden subfloor you will need to use the 6mm Ultra Tile Backer Boards, there are put onto a 4mm bed of flexible tile adhesive and then screwed down for stability. If you are going onto a concrete floor then you can use either the 6mm or 10mm insomax insulation board, these are stuck down with a 4mm bed of flexible tile adhesive. The Webtech heating mats are 3.5mm for the 150W and 200W standard mats and 4mm for the Webtech Elite mat.

Check if your tiler will be covering the heating mats with a self levelling compound as this will also mean additional height on the floor build up. It is possible to tile directly over the heating mats however a lot of tilers will prefer to cover them in self levelling compound to ensure that they have a flat surface to lay the tiles on. 

What thickness of tile to go for? Tiles can vary in thickness from 6mm Upwards and they come in all different shapes and sizes. The maximum thickness of Tile allowed over the Webtech heating mats is 30mm and generally, the thinner the better as the heat will get through easier.

2) Get a Quote

Do your Own Calculations: Measure you room and get the area in m2. Take away the fixed furniture such as wardrobes or kitchen units from your overall room size to work out the free floor area. You need to leave a border around the edge of the room and away from fixed units of between 15-20cm so the mat required will be around 80-85% of the free floor area. The area of Insulation Boards ordered should be 20% larger than the total floor area to allow for wastage.

Get Rayotec to Provide an Estimate:  If you are unsure what size you would need then you can always email a set of floor plans to Rayotec along with details of your floor coverings (ie Tiles) information about your subfloor (ie concrete or floorboards) and we will send you a quotation. Don’t forget to include your telephone number in case we have any questions. You can get in touch via our contact us page here.

Always Purchase Protective Insulation Boards: It is always advised to buy Insulation boards to make sure you get the best performance out of your system. If you do not have insulation boards below the heating mat then you will lose some of the heat down into the cold subfloor, even if you have insulation under the subfloor you will still loose some of the heat as it will always try and get to the coldest area. Always remember to check which insulation board is suitable for your subfloor.


3) Installing the Kits

Subfloor: Imperfections, such as bumps or unevenness, should be addressed before installation. This helps to ensure that the flooring sits evenly and makes good contact with the underfloor heating mats.

Installation with Testing: Install the electric underfloor heating products as per the manual. If you have any questions just give us a call or send us an E mail. It is really important that all the testing is done by an electrician before the tiles are fitted just in case the matting has been damaged during the installation. If you find that the heating mat has been damaged during the installation you can be safe in the knowledge that you are covered by Rayotec’s Worry Free Guarantee.

Let Your Flooring Acclimatise: After you have installed the Tiles do not turn on the underfloor on at maximum power. You should always start the temperature of the heating mats at a low level such at 15c or 16c and increase it gradually until you reach the desired temperature.

 Our Worry-Free Guarantee is included, so if you damage your mat during installation, we'll replace it free-of-charge. Click here to find out more.

4) Setting the Thermostat


Temperature Control: Rayotec supply a range of digital programmable thermostats that are designed for electric underfloor heating to control the room temperature. Every thermostat has a floor probe which will cut off the power to the mat if the flooring gets above a set temperature to provide protection. Certain floorings should not go over 27C and the floor probe should be programmed accordingly.


CONTACT US


Webtech 150W/m² underfloor heating mat

Webtech (150W/m2)


  • Premium quality, suitable for most rooms

  • Fully self-adhesive mats  for smoothest possible finish
  • 30 year Manufacturer's Warranty

                    BUY NOW


Electric Underfloor Heating Mat Kit for Under Tiles

We have introduced the Next Generation Elite mat to our range of complete mat kits. This unique mat provides the best of German engineering and quality. We believe it is the best mat on the market today and offers the best value for money.

The Webtech range is perfect for bonded floors. It you have a floating floors such as a wooden Laminate or Engineered Wood check out our Rayoflex & Rayomax Mat Kits.

Watch our video to discover what makes the Elite mat the top choice


Choosing the Webtech Elite mat can save you money!

Did you know that, by using the Elite mat, you can make considerable savings in the amount of self-levelling compound you require? A completely flat surface is essential for tiled or vinyl floors so a self-levelling compound is often poured over the mats to create this. The flatter your underfloor heating is, the less self-levelling compound you need to cover it.

Why do you use less self levelling compound using the Elite mat?

Elite Cold Connector from Underfloor Heating Mat

(1) Sticky mats (lay much flatter)

CrossMany other heating mats use 3 integrated strips of tape to stick them down but the areas of mat without tape can float in the liquid self-levelling compound so you need extra to cover the mat.

tickWebtech Elite is fully adhesive meaning that the whole mat sticks down so it lies flatter and won’t float in the self-levelling compound thereby reducing the amount you need to cover it.

(2) Thinner connector

CrossOther mats have a bulky, shrink wrapped ‘cold connector’ linking the power cable to the cable in the mat and increasing the amount of self-levelling compound you need to cover it.

tickWebtech Elite has a unique integrated ‘cold connector’, i.e. one continuous thin cable, so there's no bulky shrink-wrap to cover.

Reasons why using less self levelling compound is better:

  • (1) Lower material costs
  • (2) lower floor heights
  • (3) less labour time

Which Mat Suits You Best?


Webtech Elite (Sticky)

Webtech Standard

Webtech HP

Power
150W/m2 150W/m2 200W/m2
Primary Heating
(Room with standard heat-loss)
Yes Yes Yes
Fixing Method
100% Sticky Mesh (flattest possible method) 100% Sticky Mesh (flattest possible method)
100% Sticky Mesh (flattest possible method)
Cold Connector
Fully Integrated (Latest Technology) Standard Shrink Wrapped Standard Shrink Wrapped
buy now buy now buy now


Want to find our more about our other products?

We have a large range of underfloor heating mats that can be used with lots of different floor coverings, check out our range of Electric Underfloor Heating to find what's best for your project.