Electric Underfloor Heating
for a Fire Damage Restoration
When a residential flat required complete rebuilding after fire damage, the owners chose to eliminate radiators entirely — replacing them with a low-profile electric underfloor heating system installed by Rayotec.
The Challenge
A complete strip-out following fire damage presents a rare blank canvas — but raises the stakes. With flooring, wiring, and walls exposed simultaneously, every trade must plan ahead and each decision locks in the next.
The client’s priorities were clear from the outset:
- Remove radiators entirely — reclaiming wall space and simplifying the layout
- Achieve even warmth throughout, free of cold spots or hot zones near walls
- Work within tight floor-build tolerances — critical in a flat where every millimetre matters
- Future-proof the property with smart, zoned controls and efficient heating
The Rayotec Solution
After assessing the floor construction, room layouts, and planned engineered wood finish, Rayotec specified a low-profile electric heating mat system paired with Rayoboard insulation beneath. Insulation is what separates a high-performing installation from an adequate one — directing heat upward rather than into the subfloor.
The system was mapped to avoid fixed furniture zones, ensuring every square metre of usable floor contributes to heating. Smart WiFi thermostats were integrated throughout, giving the client room-by-room scheduling and remote control via smartphone.
The Result
The Halliford flat now has a heating system that matches the quality of its refurbishment. No radiators, no cold spots, no compromise — consistently warm floors, smarter controls, and more flexible living space throughout.
Because the system was integrated during the restoration rather than retrofitted afterward, the client achieved maximum performance with minimum disruption. The low-profile installation added negligible height to the floor build-up — a factor that matters considerably in a flat environment.
Why Refurbishment Projects Are Ideal for Electric UFH
Exposed floors and fresh electrical runs make underfloor heating significantly simpler and more cost-effective than retrofitting into a finished property. Electric systems require no boiler upgrades, no pipework modifications, and no wet trades — just the heating mats, insulation, and a qualified electrician.
In a flat where plumbing changes would have been complex and disruptive, electric underfloor heating was the natural, practical choice.
How the Installation Came Together
The full installation ran alongside the wider restoration programme and was completed in two days with minimal disruption to the site.
With fire restoration already exposing the concrete subfloors, every area was cleaned and checked before a single mat was laid. A solid, level base is the foundation of a reliable installation.
Exposed subfloors following fire restoration strip-out
High-performance Rayoboard insulation boards were fitted across all heated areas — the step most budget installations skip, and precisely why they underperform. Proper insulation significantly reduces warm-up times and prevents energy loss into the slab.
Rayoboard boards installed across all heated areas
Electric underfloor heating mats were laid methodically through the kitchen and living areas with consistent spacing. Each mat was electrically tested before proceeding — ensuring all elements were intact before permanent concealment beneath the floor.
Heating mats laid throughout the flat — hallway, living areas and bedroom
Smart WiFi thermostats were configured and demonstrated to the client before flooring was laid, providing full system confidence from day one — with room-by-room scheduling and remote smartphone control.
With the system signed off, engineered wood flooring was installed over the heating mats. The result: a seamless, contemporary finish — warm underfoot, clean to look at, and completely invisible as a heating system.
Can electric underfloor heating be installed during refurbishment works?
Yes — and it is often the most cost-effective time to do so. With floors already up and electrical systems being replaced, integrating underfloor heating adds minimal time and cost compared to retrofitting later.
Is electric underfloor heating suitable for flats?
Absolutely. Electric systems require minimal floor build-up and no pipework modifications, making them well-suited to flats where space is at a premium and wet underfloor heating would be impractical.
Does electric underfloor heating work beneath engineered wood flooring?
Yes, when correctly specified. Engineered wood is one of the most compatible floor finishes for electric underfloor heating — more dimensionally stable than solid wood and excellent at transmitting warmth evenly.
Can underfloor heating replace radiators entirely?
In most residential applications, yes. A properly designed electric underfloor heating system provides primary heating for individual rooms or whole properties — without a radiator in sight.
Ready to eliminate your radiators?
Rayotec installs electric underfloor heating across Surrey and the surrounding area — for refurbishments, restorations, new builds, and extensions.