Electric Underfloor Heating | Kitchen, Conservatory & Hall Retrofit | Camberley, Surrey | Rayotec
Case Study · Camberley, Surrey

Electric Underfloor Heating for a
Kitchen, Conservatory & Hall Retrofit

With three cold rooms in an occupied family home, Rayotec delivered a fully zoned electric underfloor heating system — minimal mess, maximum coverage, separate smart controls for every area, completed in just 2 days.

Detached House — Occupied Webtech 150W Mats Smart WiFi Thermostats 3 Independent Zones Completed in 2 Days
Location
Camberley, Surrey
Property Type
Detached 2-Storey House
Project Type
Retrofit — Occupied
Heating Areas
Kitchen, Conservatory & Hall/WC
Heating Mat
Controls
Smart WiFi Thermostats
Installation Time
2 Days

The Challenge

Installing electric underfloor heating in an occupied home demands speed, careful planning and minimum disruption. Rayotec worked closely with the client from the outset — walking through each room, agreeing mat coverage, selecting thermostat positions and setting a clear programme so the family knew exactly what to expect.

The client’s priorities were clear from the start:

  • Complete the installation quickly with minimal mess and disruption to daily life in an occupied home
  • Address three cold areas — kitchen, conservatory and hall/WC — with good insulation performance
  • Keep floor height increase to an absolute minimum given existing door clearances and skirting heights
  • Achieve maximum mat coverage in each room for even, consistent heat distribution throughout
  • Provide separate independent zone control for each area with remote smart thermostat access

The Rayotec Solution

Rayotec specified a Webtech 150W/m² heating mat system on 6mm Insomax insulation boards — the slimmest available profile delivering the best insulation performance within the tightest floor height build-up. A first skim of self-levelling latex was poured over the mats to encapsulate the system cleanly, with the floor fitter completing a second skim prior to laying the Amtico finish.

Coverage areas and thermostat locations were walked through room by room with the client before any work began, ensuring mat positions maximised heated area and thermostat chases were kept to an absolute minimum. Three independent WiFi thermostats were positioned and commissioned so each zone can be scheduled and controlled separately from a smartphone.

The Result

The client was delighted with the finished system. Floor height increase was kept to a minimum throughout all three areas, and smart WiFi thermostats deliver independent zone control and remote scheduling for kitchen, conservatory and hall/WC separately — all completed in two days with minimal mess in an occupied home.

The 6mm Insomax boards kept the build-up as slim as possible while still directing heat efficiently upward into the room. Rayotec left each floor fully encapsulated and ready for the floor fitter to apply the second skim of latex before laying the Amtico finish.

Why Multi-Zone Retrofits Need Careful Planning

When retrofitting underfloor heating across multiple rooms in an occupied home, zoning decisions and thermostat placement need to be thought through carefully before a single board is laid. Agreeing coverage layouts in advance avoids disruption, reduces wall channelling and ensures every room performs as expected from day one.

Electric systems are ideally suited to this type of project: no pipework, no boiler connections, and no wet trades. With slim insulation boards and a methodical approach, electric underfloor heating can be installed cleanly across several rooms simultaneously in a fully occupied property.

How the Installation Came Together

The full installation was completed in two days — all electrics on day one, the full system installation across all three zones on day two.

1
First and Second Fix Electrics

All electrical work was completed on day one — first and second fix carried out together, with three separate thermostat circuits installed for the kitchen, conservatory and hall/WC zones. Thermostat back-box positions were agreed with the client beforehand to keep wall chasing to a minimum. Getting the electrics right first ensures a clean, uninterrupted system installation to follow.

First fix electrics — Camberley underfloor heating installation

Electrical circuits installed and thermostat locations confirmed with the client

2
Subfloor Preparation — Clean and Prime

Each area was swept and primed across the kitchen, conservatory and hall/WC before any boards were laid. A clean, properly primed substrate is the foundation of a reliable, long-lasting installation — a step that should never be rushed regardless of how tight the programme.

Subfloor cleaning — Camberley underfloor heating retrofit
Subfloor primed and ready — Camberley

All three areas cleaned and primed ready for Insomax boarding

3
Insomax 6mm Board Installation

6mm Insomax insulation boards were laid throughout all three zones using flexible tile adhesive. The 6mm board was specified deliberately to keep the floor height increase to the absolute minimum while still delivering meaningful insulation performance — directing heat upward efficiently and reducing warm-up times. In a retrofit with existing door clearances and skirting heights, controlling build-up is critical.

Insomax 6mm boards being laid — Camberley
Insomax boards covering full area — Camberley

6mm Insomax boards installed across all three heated areas with flexible tile adhesive

4
Heating Mat Installation

Webtech 150W/m² heating mats were installed across the kitchen, conservatory and hall/WC, with coverage layouts planned in advance with the client to maximise the effective heated area in each room. Each mat was electrically tested before proceeding to ensure every element was intact prior to encapsulation. Independent cold tails were routed to each of the three thermostat positions.

Webtech 150W heating mat unrolled — Camberley
Heating mat coverage close-up — Camberley
Heating mat laid in kitchen — Camberley
Heating mat laid in conservatory — Camberley

Webtech 150W mats installed and tested across all three zones

5
Latex Skim

A first skim of self-levelling latex was poured over the heating mats in each zone to fully encapsulate the system and create a smooth, protected surface. A second skim is then applied by the floor fitter prior to laying the Amtico, ensuring a perfectly flat base and a clean handover between trades.

Self-levelling latex being poured over heating mats — Camberley
Latex skim cured and ready for floor fitters — Camberley

Self-levelling latex skim encapsulating the heating mats across all three zones

6
Smart Thermostat Commissioning & Handover

Manuals were sent to the client covering how to use the thermostats, including independent room-by-room scheduling and remote smartphone control. The floor was left fully encapsulated and ready for the floor fitter to apply the second skim of latex before laying the Amtico finish.

Can electric underfloor heating be retrofitted into an occupied home?

Yes — and with the right planning it can be done with very little disruption. Electric systems require no pipework or boiler modifications, meaning the installation is contained to the floor itself. With an experienced installer, multiple rooms can typically be completed within two days.

Why use 6mm insulation boards rather than thicker alternatives?

Floor height was a key constraint in this retrofit. The 6mm Insomax boards were chosen to keep the build-up to an absolute minimum while still delivering meaningful insulation performance — directing heat upward rather than into the subfloor and reducing warm-up times. In most occupied retrofits, controlling floor height is as important as thermal performance.

Is electric underfloor heating suitable beneath Amtico flooring?

Yes. Amtico and other luxury vinyl tile floors are fully compatible with electric underfloor heating and are excellent thermal conductors. The combination delivers even, consistent warmth without the risk of thermal stress that can affect natural materials.

How do smart WiFi thermostats benefit an electric UFH system?

Smart thermostats allow room-by-room scheduling and remote control via smartphone — so each zone can be adjusted or pre-heated independently from anywhere. With three separate zones in this project, the client can heat only the areas they are using, reducing running costs compared to a whole-house system.

Can a conservatory be heated effectively with electric underfloor heating?

Conservatories are often the coldest rooms in a house and are typically under-served by standard radiator systems. Electric underfloor heating is ideal — it can be installed quickly as an independent zone, provides even warmth at floor level, and requires no additional plumbing connections to the main heating system.

What is the benefit of separate zone control?

Independent zoning means each room is only heated when occupied and needed. Kitchen, conservatory and hall/WC often have very different usage patterns throughout the day — separate WiFi thermostats with individual schedules ensure the system runs efficiently without heating empty rooms unnecessarily.

Ready to upgrade your home heating?

Rayotec installs electric underfloor heating across Surrey and the surrounding area — for retrofits, refurbishments, new builds, and extensions.